RIG: - Lot 8

Lot 8
Go to lot
RIG: - Lot 8
RIG: RIG (Warning: Live Auction not available on this lot. Please contact the auction house. 100 000euros deposit required) * RIG CARRIER - DRILLMEC comprenant: - SEMITRAILER - SARA C.M. MT.1360/10 - POSITIONNING CONTROL PANEL - DRILLMEC - STABILIZERS (x4) - AUXILIARY HPU - OLEOBI A01.01022.02.00 - ELECTRIC MOTOR ABB M2QA200L4AB35 (34,5kW/45HP) - HYDRAULIC PUMP PARKER DENISON PV202R1EL02 - OIL RESERVOIR 700L(186gal) - BOP HANDLING SYSTEM 2 X HYDRAULIC JACKS OF 20 T CAPACITY EACH * RIG STRUCTURE - DRILLMEC comprenant: - SUBSTRUCTURE (DRILL FLOOR / DOG HOUSE SUPPORT / RIGFLOOR WORKSHOP SUPPORT / PIPE HANDLER STRUCTURE / HPU SUPPORT / TRAILER SUBSTRUCTURE) - SKIDDING SYSTEM (SKIDDING STRUCTURE / PANTOGRAPH / SKIDDING POWER UNIT) - WALKWAYS, HANDRAILS, STAIRWAYS & CABLE TRAYS * MAST - DRILLMEC TELESCOPIC HYDRAULIC comprenant: - FIXED SECTION: MAST RAISING CYLINDERS(x2) - DRILLMEC POA807330 (Dxd 250x220 mm - course 2305 mm) - TELESCOPIC SECTION: MAST ELEVATION CYLINDER - DRILLMEC (Dxd 450x380 mm - stroke 8300 mm) - CROWN BLOCK (CAPACITY 272 m.T): DRILLING LINES SHEAVES(x8) - DRILLMEC 8 sheaves of 1m diam for 1 "5/8 cable - 4 RAISING LINES - SIRTEF D 42mm / MT.29/60 (1"5/8 with minimum strength of 165 KdaN) - PULL DOWN SET - PULL DOWN SHEAVES(x2) - DRILLMEC - PULL DOWN WIRE ROPES DIAM 20mm (x2) - DRILLMEC - PULL DOWN CYLINDERS(x2) - DRILLMEC (Dxd 125x70 mm - course 700 mm) * CRANES & WINCHES comprenant: - MAST SERVICE CRANE - DRILLMEC - HYDRAULIC DRILLMEC 4 T 000 auxiliary service crane on mast side with hydraulic winch for rig floor service (WINCH / CRANE ROTATION SYSTEM / CRANE CONTROL PANEL / SERVICE CRANE WIRE ROPE) - PH JIB CRANE - BREVINI - 013AC006072 / DRILLMEC 12 T 000 jib crane on pipe handler with hydraulic winch for service rig - WINCH HYDRAU MOTOR - SAMHYDRAULIC 11CR M 1086ESA0 - OVERDRIVE - BONFIGLIOLI 306L215.3HC5 - JIB CRANE WIRE ROPE - SIRTEF D24x50m * DOG HOUSE DRILLMEC (DRILLING OPERATIONS CONTROL PANEL / PIPE HANDLER CONTROL PANEL) * PIPE HANDLER - DRILLMEC FULL AUTOMATIC comprenant: - BASE - ROTATION ELECTRIC MOTOR - SIEMENS 3~ 460v-60Hz 6.5Kw, 1MJ61634CA96-Z - ROTATION HYDRAULIC MOTOR - PARKER F11-10-FM1B-CN-K - LOWER ARM - HORIZONTAL TRANSLATION ELECTRIC MOTOR - SIEMENS 3~ 460v-60Hz 1Kw, 1MJ60964CA91-Z - FINGER CLAMP - UPPER ARM - HORIZONTAL TRANSLATION ELECTRIC MOTOR - SIEMENS 3~ 460v-60Hz 1.5Kw, 1MJ60974CA91-Z - 2 OVERDRIVE - BONFIGLIOLI ( 1 x X_305L3772HC4LP160A et 1 x X_303L244.6HC4A P90AS048A) - VERTICAL LIFTING HYDRAU MOTOR - PARKER F12-125-MF-IV-D-000-000-0 (PN3785866) - WIRE ROPE - CLAMP * ROTATING EQUIPMENT comprenant: - TOP DRIVE - DRILLMEC HTD 300 - TDS POWERING SYSTEM = TROIS HYDRAULIC MOTORS - DENISON H14V3N1A8A8B10 - AIR BRAKE SYSTEM - MAIN SHAFT - MT.366/11 - DOLLY SLIDING SYSTEM - MT.12/09 - DOUBLE HOOK - DRILLMEC NH.136558 Type double hook integrated in top drive - GOOSE NECK - DRILLMEC TQ 01 - TDS COMPENSATORS - DRILLMEC - ROTARY TABLE 27 ½” HOLE (can be removed to allow 47'' passage through substructure) - 2 HYDRAULIC MOTORS - M+S HYDRAULIC MV315 C/2 - AUTOMATIC SLIPS SYSTEM - CASING BACK-UP TONG / BIT BREAK-OUT - MOUSE HOLE - POWER TONG - DRILLMEC D 3.1/2" à 11" - TORQUE WRENCH - DRILLMEC HYDRAULIC HTD 301 - CASING MAKE-UP DEVICE - DRILLMEC * STAND PIPE MANIFOLF - DRILLMEC 4"ID -5000psi drill floor manifold mounted on skid * HP LINES - DRILLMEC comprenant: - MAST STAND PIPE 4''ID 5000psi (between stand pipe manifold and mast) - DRILLING ROTARY HOSE 3 1/2" ID 5000psi (From top mast to TDS) - MUD PUMPS HP HOSES (HP LINES RIGID) * 21 PIPE BINS
My orders
Sale information
Sales conditions
Return to catalogue